How to Fix a Falling-Apart Kitchen Drawer the Easy Way
This kitchen cabinet drawer has served faithfully for 20 years, but with constant use one corner crumbled and the drawer front started falling off. Off-the-shelf corner brackets from Amazon or your local hardware store can rescue a drawer like this, but I made my own from stainless steel I already had. With some glue, clamps and my homemade brackets reinforcing the corners, the drawer is almost like new, or maybe better.
This is how I fixed my drawer. Wear eye protection when drilling metal, follow at your own risk, and use proper safety precautions.
Before You Begin: Decide What Can Be Saved
Check the condition of the wood. If it were in worse shape, I’d think about replacing some of it. Mine could get away with just gluing back together. The steel brackets that came with the drawer weren’t stainless, so I decided to make new ones that won’t rust.
Tools & Supplies Used
Disclosure: Some of the links below are affiliate links. As an Amazon Associate, I earn from qualifying purchases. If you choose to buy through them, it helps support my work at no additional cost to you.
- Step drill bit, 1/8″-1/2″ cobalt https://amzn.to/4djKPMm
- TOOLEAGUE 9-piece punch and chisel set https://amzn.to/4djsor0
- #8 stainless self-tapping sheet metal screw kit (180 pcs) https://amzn.to/4kpJxBV
- Mr. Pen wood screw assortment kit (152 pcs) https://amzn.to/44KtObY
- Stainless steel L bracket corner braces (40 pcs) https://amzn.to/44FhvOd (if you’d rather buy brackets)
- Heavy-duty L-shaped corner bracket set (20 pcs) https://amzn.to/4j5x2Kz
- Titebond II Premium wood glue https://amzn.to/3GZ53ix
- Long clamps (you can never have enough clamps)
- A vise for bending the brackets
- Drill and screwdriver
Step 1: Take the Drawer Apart
I removed the drawer front and took the rails off so I could get at the broken corner.
Step 2: Glue and Clamp the Corner
I cleaned out the joint and glued it back into place. The bottle of Titebond I found had been left in a freezing garage all winter, even though the label says to keep it from freezing, and it was very runny. I used it anyway and clamped everything tight with long clamps. It turned out sticky and it did set, so I left it overnight.
Step 3: Bend Your Own Stainless Brackets
The drawer front already had holes for its screws, so I bent strips of stainless steel into L-shaped brackets in the vise, positioned so new holes would line up with those screws.
Step 4: Mark, Punch and Drill the Holes
I marked the brackets, made a starting dimple with a center punch and drilled with a step drill. The original holes measured 5/16″, so I drilled the same size to leave a little wiggle room for the screws. Clamp the bracket well. Mine needed a better clamp partway through. Then clean up the edges so they sit flush.
Step 5: Screw the Brackets to the Drawer
I drilled a couple of smaller holes for the screws that attach the brackets to the drawer sides. The self-drilling screws from my kit fit the bit well and go straight in with no pilot hole. One was poking out the side slightly, but not enough to be a problem. Work one side while the glue on the other side dries.
Step 6: Reattach the Rails and the Front
After the glue sat overnight, I took off the clamps, cleaned up the mating surfaces and test-fitted the front. I had put the rails on inside out at first, so check that the wheel ends up on the correct side. Then I tightened the screws.
Final Thoughts
With glued corners and stainless brackets, this 20-year-old drawer is almost like new and should be stronger than before. If you don’t have scrap stainless, ready-made corner brackets will do the same job.