How to Change All 5 APEC RO Filters: Don’t Wait as Long as I Did
We’ve had this APEC 5-stage reverse osmosis system (ROES-50 Essence) for a few years, and this was the first time I changed all five filters at once. It had been about a year since I changed anything, and there was considerable buildup inside. Don’t wait as long as I did! Here’s my step-by-step process for getting the filters out, cleaning the housings and putting everything back.
This is just how I do it on my system. Check your own manual, follow at your own risk, and keep a towel handy for drips.
Before You Begin: Write Down the Date
Tip #1: keep a record. In recent years I’ve written down when I change something on the unit, which is very helpful because we forget. I also find it much easier to take the whole unit out from under the sink and work on it at the bench.
Tools & Materials Used
Disclosure: Some of the links below are affiliate links. As an Amazon Associate, I earn from qualifying purchases. If you choose to buy through them, it helps support my work at no additional cost to you.
- APEC Essence Series 50 GPD complete replacement filter set (FILTER-MAX-ES50) https://amzn.to/3CUSUcs
- An old cloth or container to catch water
- Dish soap for cleaning the housings
- A flat tool (I used a chisel) to ease out the old RO membrane
- A vise helps when opening the membrane housing
- Clean cloth
Step 1: Shut Off the Water and Relieve the Pressure
Turn off the supply. Mine shuts off the water to the faucet as well as the filter unit. Then turn off the tank ball valve and briefly open the filtered water faucet to relieve the pressure.
Step 2: Disconnect the Pipes and Remove the Unit
I disconnected four pipes: the red one from the water supply, the drain line (it says do not remove the flow control inside, so leave that little tip alone), the line to the tank and the line to the faucet. Push in the collar and pull each pipe out, with something ready to catch any water, because the tank line drips. My unit just hangs on the cabinet wall, so it lifts right off.
Step 3: Remove Stages 1, 2 and 3
On the bench, I unscrewed the three big housings one by one. The stage 1 sediment filter looked like it should have been changed a while ago, and the stage 2 and 3 carbon filters were dark too. I hadn’t over-tightened them last time and they never leaked, so they came off easily. The moral of the story: change your filters on time.
Step 4: Clean the Housings and Check the O-Rings
I poured out the housings and cleaned them with a little dishwashing soap. You can buy new O-rings. Mine were changed last year, so I reused them. If you’re worried about a trace of soap, the system needs to run for a while anyway to flush out the carbon.
Step 5: Replace the Stage 5 Carbon Filter
Before putting the three big filters back, I changed the two filters on top. Release the clips, push in the fittings to free the pipes, and clean the top of the bracket while you’re there. Stage 5 is easy because there’s nothing to disassemble.
Tip #2: keep your spare filters somewhere you can find them when you need them, preferably right next to the unit.
Step 6: Replace the Stage 4 RO Membrane
Having a vise really helps here. I was afraid of breaking the plastic case, but it wasn’t that hard. The old membrane is held in by its rubber seal, so I used a chisel to ease it out, then rinsed the housing. The new reverse osmosis membrane comes with seals already on the end. It eased in, and when I tightened the cap it popped all the way into place.
Step 7: Install the New Sediment and Carbon Filters
The three housings are identical, so it doesn’t really matter if you mix them up, but I label mine. Stage 1 is the sediment filter, which takes out the big particles before the water reaches the two carbon filters. I prefer genuine APEC filters because I trust the materials. Make sure there’s a rubber seal on each end.
Tip #3: tighten as you go. Especially the middle housing. Once the two on either side are on, it’s hard to get at it.
Step 8: Reconnect the Pipes
Back under the sink, I reconnected each pipe: white to the faucet from the final filter, black to the drain (leave the little check valve on that line in place), red from the water supply into the first filter, and yellow to the tank.
How the Water Flows Through the System
It helps to understand how it works. Water comes into the sediment filter, then through the two carbon filters, through a valve and into the RO membrane. From the membrane, one line goes to the drain and the other goes to a T that feeds both the tank and the final (stage 5) filter, which goes to the faucet. When the faucet is off, the system fills the pressurized tank. When you open the faucet you get water from the tank plus whatever the filters can supply.
Final Thoughts
I wrote the date on the unit again, and the water is tasting good. Don’t leave yours as long as I did. Your filters will thank you. When it’s time to replace the storage tank itself, see how I replaced my RO water tank.
One Comment