How to Drain a Water Heater Tank the Right Way, Step by Step
There are all kinds of opinions on how to drain a water heater. Some master plumbers even say that if it’s been more than a couple of years, you’d better not do it. I’m a little suspicious about that. There are some good reasons to drain the tank regularly to extend its life and improve efficiency, so here’s how I drained mine, what to expect, and why the maintenance matters.
Hot water can burn you. This is how I did it on my gas heaters. Follow your heater manufacturer’s instructions, follow at your own risk, and use proper safety precautions.
Why Flush Your Water Heater?
I asked Copilot about the risks of not flushing, and here’s what it listed:
- Bacterial growth: sediment layers create warm, stagnant zones where bacteria can thrive, which can lead to foul-smelling water.
- Contaminated water: sediment may contain rust, sand and other debris, and in rare cases can leach harmful metals or compounds.
- Reduced efficiency, which can raise your energy bills, and reduced capacity, since sediment takes up space.
- Premature failure: trapped heat accelerates corrosion and can shorten the tank life by 2 to 5 years.
- Noise and overheating: the popping or rumbling you hear on older heaters is a sign of steam bubbles trapped under sediment.
Its best practices: flush once a year (every 6 months in hard water areas), consider a water softener or filter, inspect the anode rod every 1 to 3 years, and keep the temperature around 120°F to reduce mineral buildup and bacterial growth. I did not know that last one.
What You’ll Need
- A garden hose for the drain valve
- A big container to catch the water
- A second container with a T-shirt over it to see what sediment comes out
- A screwdriver, if your heater still has the standard plastic drain valve
Step 1: Turn the Burner to Pilot
You don’t need to turn off the gas completely and relight the pilot afterwards. That’s a waste of time. Just turn the gas control from On to the Pilot position, so the pilot stays lit but the burner won’t fire up.
Step 2: Use Up the Hot Water First
Go take a shower and use up some hot water, then wait. That way, if you get splashed, the water in the tank isn’t hot enough to burn you. I left mine for several hours.
Step 3: Shut Off the Water and Open a Hot Tap
Turn the cold water valve on the heater 90° to the pipe to shut it off. Then open a sink faucet on the hot side. That lets the tank breathe, so there’s no vacuum when you drain water out.
Step 4: Attach a Hose to the Drain Valve
I had already replaced the standard plastic drain valve with a brass one, which doesn’t need a screwdriver to open like the original does. Here’s how I swapped the plastic drain valve for brass.
Some people say to run the hose outside, and that’s not a bad idea if your water heater is above ground level. If it’s below ground level like mine, gravity won’t drain it once the water gets down to a certain level, so I drained into containers instead.
Step 5: Drain in Batches and Check the Water
Open the drain valve and fill the container, close it, dump it, and repeat. My first batch came out a little cloudy, and the second had some particles in it. I wondered if those were from the anode rod. Later I filled the container directly from the drain valve. The flow is quite strong, so don’t overfill it or you’ll spill water getting it out from under the valve.
As the pressure drops you’re getting close to empty. Near the bottom I saw some murkiness, but no rust, which is a good sign. If there were rust, I’d be really concerned about the water heater.
Step 6: Refill and Restore
I don’t show the refill in the video, so follow your heater’s instructions to refill the tank completely before you turn the gas control back from Pilot to On.
Final Thoughts
I saw some little bits and pieces at the end, which probably means the anode rod is doing its job and the tank is still good. Speaking of anodes, here’s how I changed the anode rods on these heaters. Coming up, I’ll be installing powered anode rods on these same water heaters and comparing the most popular rods on the market.