How to Recaulk a Bathtub: The Best Tools and Tips for a Clean Line
If you have an old bathtub where the caulking is cracked, peeling or full of mold, you’re in the right place. Proper bathtub caulking is critical to preventing water damage and mold. In this project I tried out some time-saving tools and I’ll share the tips I picked up along the way for a clean, watertight finish.
This is my experience on my tub. Work with good ventilation, follow the caulk manufacturer’s directions, and follow at your own risk.
Before You Begin: Preparation Is Everything
For jobs like this, the preparation determines a lot of the outcome. A contractor probably wouldn’t do every step I did, but when you’re doing it yourself you can make sure the job is the best it can possibly be.
Tools Used
Disclosure: Some of the links below are affiliate links. As an Amazon Associate, I earn from qualifying purchases. If you choose to buy through them, it helps support my work at no additional cost to you.
I was happy with all of these.
- ALLWAY CT31 3-in-1 caulk tool (removal and smoothing) https://amzn.to/3ZIQ7KP
- Gorilla Waterproof Caulk & Seal 100% Silicone, white, 10 oz https://amzn.to/3ZUM4MV
- Sausage caulk gun, 20 oz / 10 oz dual-purpose, 18:1 thrust https://amzn.to/3DxXMUQ
- Scotch-Brite Heavy Duty scour pads https://amzn.to/4ggFWEs
- 180-3000 grit sanding sponge set https://amzn.to/4gI3D8n
- A file (for sharpening the tools)
- Putty knife
- Rubbing alcohol
Step 1: Sharpen the Removal Tool
The ALLWAY tool has a blade end for removing caulk. Out of the package the pulling action was OK, but it didn’t scrape well along the tile. I went over the edges with a file to make them sharp, and that made a huge difference. It cuts into the old caulk like butter. The plastic part is good for running along the tub edge because it doesn’t scratch, although it can’t reach into the corners.
Step 2: Scrub and Scuff the Surface
I cleaned out the joint with a Scotch-Brite pad. Then I went around the edge and into the corners with a fine sanding sponge to help the sealant make good contact with the tub and tile. It also lifted bits of old silicone and dirt, so it’s a good extra step.
Step 3: Sharpen Your Putty Knife Too
My putty knife was worn at the end, so I did the same thing with the file. With a sharper edge, stubborn old caulk comes off a whole lot easier. Finish by wiping everything down with alcohol.
Step 4: Lay a Big Bead and Try Not to Touch It
Some of the gaps were quite wide, so I needed a fairly big bead. I was taught long ago that if you put caulk down right in the first place, you don’t have to touch it, so that was my goal. I used a big sausage-style gun I’d received to review. When you let go of the trigger it stops pushing (you can change that setting), and the long trigger pull means you don’t have to keep letting go. The Gorilla silicone was more runny than I expected, but it flows very well. The idea is to keep moving and not stop. I did a second pass in the opposite direction where needed.
Step 5: Smooth With the Right Tip
The other end of the 3-in-1 tool comes with three tips of different radius. I used the largest. It’s like a silicone rubber, and the wiper contacts both the tub and the tile at the same time, so you can feel it wiping as you drag it along. I blended the corners and touched up only where needed.
Final Thoughts
A couple of days after finishing the job, it looks pretty good. Sharpen your tools, take your time on prep and don’t overwork the bead. If you’re dealing with a much bigger gap, see what happened when I caulked large gaps around a bathroom sink.