How to Install a Jack Post for a Sagging Crawl Space Beam the Right Way

With the concrete footing poured and cured, it was finally time to put a permanent support under the sagging triple beam in my crawl space. In this video I install a Tiger Brand Super S JS36 jack post, anchor the base plate into the footing, screw the top plate into the beam and then start raising it, very gently.

I’m a homeowner learning as I go, not a contractor. This is just how I did it on my house. Check your local code, follow at your own risk and wear proper eye and lung protection.

Before You Begin: Don’t Force the Beam

The goal is to raise the beam slowly over time, not all at once. On the first day I only raised it about 1/16 inch without putting too much force on it, and I plan to adjust it gradually. If the post won’t move without a lot of effort, stop and come back another day.

Tools & Materials Used

Disclosure: Some of the links below are affiliate links. As an Amazon Associate, I earn from qualifying purchases. If you choose to buy through them, it helps support my work at no additional cost to you.

  • Tiger Brand Super S JS36 jack post (two tubes, one inside the other, reaching up to 36 inches)
  • OX 3lb Hammer https://amzn.to/4ziFL5w
  • Avid Power Angle Grinder https://amzn.to/3S8yzbu
  • Diamond Concrete Grinding Wheel https://amzn.to/4zcQ8rH
  • Jackson Face Shield https://amzn.to/4qkwJkr
  • Red Head True Bolt anchors for the base plate
  • Hammer drill and an air compressor for hole cleanup
  • Simpson Strong-Tie SDS heavy-duty screws for the top plate, with a 3/8″ drive and adapters
  • Brake caliper grease for the adjustment threads
  • A dust mask (a good idea when grinding concrete)

Step 1: Grind the Footing Flat and Level

I wanted the top of the footing nice and flat so the base plate wouldn’t rock. I used the angle grinder with a diamond wheel, wore my face shield and tried not to make too much dust. Then I let the dust settle and checked that the post would sit centered under the beam.

Step 2: Drill and Clean the Anchor Holes

With the plate in position I marked the holes and drilled them with my hammer drill. The packet says to drill a quarter inch below where the anchor bottoms out. I cleaned out the holes with an air compressor, which kicks up a lot of dust.

The anchors here really only control side-to-side movement. The ones I bought turned out to be overkill for the holes in the bracket, so I decided to use just two of them.

Step 3: Set the Expanding Anchors

The anchors go in with the nuts on. Once they’re in place and you start tightening, the collar expands and locks into the concrete. Tighten them down to hold the base plate.

Step 4: Attach the Top Plate to the Beam

My beam is a triple beam, and the top plate fits nicely so it screws into both the inner and outer beams, two screws on each side. I used Simpson Strong-Tie SDS heavy-duty connectors, which are self-drilling, driven with a 3/8″ drive setup and some adapters.

Step 5: Grease the Threads

I added brake caliper grease to the adjustment threads for smoother operation. If it works on a car in all kinds of weather, it should be fine here. Concentrate it toward the top of the thread, which I realized a little late.

Step 6: Raise the Beam a Little

I used a laser line and pencil marks to see how far the beam moved, aiming for about an eighth of an inch. It did move without much effort, but I stopped at roughly 1/16 inch and left the post to carry the load. I’ll come back and adjust it gradually.

Final Thoughts

This jack post will stabilize the beam while I keep working on the crawl space. Next up is preparing the crawl space floor and putting down a vapor barrier. If you missed it, here’s how I poured the footing this post sits on.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *