How to Fix a Noisy Kenmore Whirlpool Dryer the Easy Way
Our Kenmore dryer had started making a racket. I had bought a low-cost repair kit some time ago with drum rollers, an idler pulley (tensioner) and a belt, so I opened it up to see if that would fix the problem. It did. It’s a whole lot better than it was.
This is a gas dryer, but it still has electric, so pull the plug before you start. This is my experience on my dryer. Follow at your own risk.
Before You Begin: Check the Kit Fits
The kit I used fits a list of Kenmore and Whirlpool dryers. Check the listing for your model before you buy.
Tools & Parts Used
Disclosure: Some of the links below are affiliate links. As an Amazon Associate, I earn from qualifying purchases. If you choose to buy through them, it helps support my work at no additional cost to you.
- 4392065 dryer repair kit with 349241T drum roller kit, 691366 idler pulley and 341241 belt (Techecook, for Whirlpool and Kenmore dryers) https://amzn.to/3M9amLw
- A drill or driver with an 8 mm socket
- A thin blade or screwdriver
- 600 grit emery paper
- Brake grease
- Something to support the drum
Step 1: Open the Top
Take out the lint screen, then push in the release clips at the front and the top pops open. My washer was in the way, so I pulled the dryer back before lifting the top up.
Step 2: Take Off the Front Panel
Remove the screws holding the front cover (an 8 mm socket on a drill saves time). Disconnect the electrical connection. Mine had a little tab to push, and a blade behind it helped wiggle it apart. When the front comes off, the drum drops down because it’s no longer supported.
Step 3: Release the Belt and Lift Out the Drum
Reach underneath and release the tensioner to get the belt off. The belt goes around the tensioner and hooks around the drive motor pulley. Then lift the drum out.
Step 4: Find the Problem and Clean Up
I found the problem right away: a drum roller that wasn’t supposed to look like that. The bearing material was worn out. Before going further, take the chance to clean up the inside. Mine was disgusting.
Step 5: Replace the Drum Roller
To get at one roller I removed the heat shield over the combustion tube (it has a tab that goes into the back), plus a screw and a clip holding the roller’s bracket. With the roller off, I cleaned up the shaft with 600 grit emery paper. It felt fine.
Someone had put grease on the other roller and it was still doing a good job, so I put some brake grease on the shaft. Push the triangle washers into the grooves. Don’t be too soft with them. Fingernails or thumbnails really help. Then put the bracket and screw back on.
The second roller only had one triangle washer. It turns out this wheel is allowed to travel in and out, which is probably by design, so the grooves are in different places. I fitted it the same way, with brake grease and the other washer.
Very important: don’t forget to put the heat shield back. It had more holes than screws, so I put back the two screws it originally had.
Step 6: New Idler Pulley and Belt
The old tensioner didn’t look that bad, but since I had a new one, it went in. Put the new belt around the drum with the ribs facing the drum, following the mark where the old belt was, and lift the drum back in.
Underneath, the idler’s two forks go into the hole in the base. Make a little loop in the belt (not twisted), thread it through the idler, and get it over the motor spindle. This is where it’s good to take pictures when you take things apart. I checked the video I took earlier to see how it went back together.
Step 7: Center the Belt and Reassemble
Turn the drum a little so the belt finds its position, then support the drum again while you put the front back on. The front panel has a lip at the bottom. Line it up with the drum, pull it up into place, and put the screws back in. Reconnect the wiring, close the lid, and put the last screws back.
Final Thoughts
With new rollers, an idler and a belt, the noise is a whole lot better. I also noticed the felt washer may need replacing, but for now it’ll be just fine. A low-cost kit was all it took.